I began construction with the turret. The main gun is moulded in two halves, and it does take some careful sanding to remove evidence of the join. The upper and lower halves of the turret itself join on what would be a weld line on the original, and this continues at an angle to meet the top edge. It was fairly simple to sand a small bevel on the joining surfaces and add a small piece of plastic rod to replicate the weld.
Then I added the canvas blast-shield. I used tissue paper and PVA glue, carefully building up layers to achieve a suitably wrinkled look. I also added a small extension tube in front of the co-axial mg using clear plastic tubing, as that is what most photographs seem to show. It took several attempts to get a reasonable look, but I’m not too unhappy with the result.
I added the hatch and other parts to the turret and gave the canvas screen a quick coat of acrylic dark green, which showed up a couple of areas that needed further work. I also added a little filler to the rear of the turret to cover some small gaps.
Then, the turret got a coat of Vallejo spray olive drab.
Then I added the decals (I’m going for a tank of the JGSDF) and painted the canvas screen.
Next, I started work on the hull. The holes in the lower hull were filled using pieces of plastic card and Tamiya white putty.
I added the driver’s hatch and other parts to the upper hull and joined the upper and lower hull halves. Don’t forget to add the ends of the exhausts before you join the upper and lower halves of the hull – they insert from underneath. In retrospect, I should also have added some clear plastic to the interior of the driver’s vision slots – these are fairly large and obviously open on the finished model.
Then the hull got a coat of olive green and the exhausts were given some rough texture with Tamiya white putty and painted a rust colour – most photographs seem to show well rusted exhaust shields on M41s. I also added the decals to the hull at this stage.
Both hull and turret were given some light chipping before both were treated to a coat of clear varnish.
Then I added some shadows and general staining on both turret and hull with Abteilung Oils Dark Mud, which is actually a dark grey. I also applied a wash of dark brown oil to the canvas screen.
The Sprockets, roadwheels, return wheels and Idlers are all very cleanly moulded. I painted the tyres dark grey, a fairly easy task because there is a clear distinction in these parts, then these too were given a coat of varnish and a wash of Dark Mud.
The tracks were painted a fairly light gunmetal, the rubber blocks were painted dark grey and then a brown wash was applied to these, the running rear and lower hull.
Then it was on to final assembly. The only change I made was to replace the radio antenna with some thin plastic rod, though I kept the kit bases. With the addition of some streaks on the hull and turret using white oil paint, it was finished…
After Action Report
I accept that this is not the most detailed or accurate 1/35 armour kit available, but, here’s the thing; I really enjoyed this build, far more than some other recent builds. Why? Well, it’s a simple and straightforward build for one thing. There is nothing challenging or complex here and very few tiny parts to be eaten by the carpet monster. Enjoyment is an under-rated factor in kit-building – after all, most of us do this for pleasure and relaxation and for me, this one really hit the spot.
Other than attempting to create a canvas screen round the mantlet and making a weld-bead on the turret, this is entirely out-of-the-box. I know, there are lots of other things I could have done including fabricating a tow cable, adding the strengthening struts on the side of the stowage boxes and other bits and pieces but you know what? I don’t care. I’m satisfied with the finished result and creating it provided me with several hours of pleasure. Add that to the fact that this is a very low-cost kit and you have something that is close to the definition of cheap and cheerful.
Despite its age, the parts in this kit are cleanly moulded, everything fits well and there is nothing complex or fiddly involved construction or painting. This is, in every sense, an old-school kit. You have to be prepared to either put in some time to make improvements or to simply accept this for what it is – a reasonable but not perfect representation of an M41. With those caveats, I heartily recommend this kit to anyone looking to while away a few pleasant evenings.
Now, all I need to find is a 1/35 Godzilla foot so I can build an appropriate diorama…
Tamiya 1/35 Walker Bulldog (MM155) In-Box Review and History